Hello,
After reading a lot of instructions and thread and dealing with some technical problems I stuck at some point and I really need a pro advice.
I bought this kindle from ebay as bricked thinking it would be an easy fix. Apparently I was wrong. The seller claimed it is not used for a long time and it didn't work after 4 hours charging. When I get it realized factory refurbished.
So, When I get it,
- I tried, 2 days charging with a wall charger and resetting by holding 20 and 40 seconds
- Opened it, it was very clean there isn't any sign of amateur work.
- tested battery, it is ok.
- made a serial connection, here is my first screen,
Code:
U-Boot 2009.08-lab126 (Jun 29 2019 - 10:27:24)
CPU: Freescale i.MX6 family TO0.0 at 996 MHz
Temperature: 36 C, calibration data 0x59a5205f
mx6sl pll1: 996MHz
mx6sl pll2: 528MHz
mx6sl pll3: 480MHz
mx6sl pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 24000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
Board: Muscat WFO
Boot Reason: [ POR ]
Boot Device: NAND
Board Id: 067070918133198Y
S/N: G090KBxxxxxxxxxxx
I2C: ready
DRAM: 512 MB
Using default environment
In: serial
Out: serial
Err: serial
Quick Memory Test 0x80000000, 0x1fff0000
POST done in 111 ms
Battery voltage: 4154 mV
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.0.35-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2952672 Bytes = 2.8 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.096583] boot: C def:bcut:batterycut=1
[ 0.263949] pmic_soda_connects_notify_otg_out:423
[ 0.280222] LPDDR2 MfgId: 0x5 [Nanya]
[ 0.284076]
[ 0.284079] just text: vaddr c0131fdc, va 0xc0131200 pa 0x801000c3 attr 0x6
[ 0.292358]
[ 0.292361] nmx6sl_wfi_iram: vaddr e084e000, va 0xe084e200 pa 0x904043 attr 0x2
[ 0.305407]
[ 0.305410] mx6sl_ddr: vaddr e0856000, va 0xe0856200 pa 0x905043 attr 0x2
[ 0.313728]
[ 0.313731] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149
[ 0.322453]
[ 0.322456] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149
[ 0.330842]
[ 0.330844] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149
[ 0.340917]
[ 0.340919] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149
[ 0.354354]
[ 0.354357] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149
[ 0.363294]
[ 0.363296] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149
DEBUG:recovery-util.c:1680:setup_die_signals():Installed signal handlers.
3.0.35-lab126 #2 PREEMPT Tue Jul 24 06:43:56 PDT 2018 armv7l
Press [ENTER] for recovery menu... 0 /BOOTING DEFAULT.
IP-Config: no devices to configure
kinit: Mounted root (ext3 filesystem) readonly.
I couldn't see any error and reboot in to diags menu. There were some errors but it I could see the menu on the touch screen.
Code:
Hit any key to stop autoboot: 0
uboot > bootm 0xE41000
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.0.35-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2635252 Bytes = 2.5 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.098553] boot: C def:bcut:batterycut=1
[ 0.285357] LPDDR2 MfgId: 0x5 [Nanya]
[ 0.289259]
[ 0.289263] just text: vaddr c0150d44, va 0xc0150200 pa 0x801000c3 attr 0x6
[ 0.301812]
[ 0.301816] nmx6sl_wfi_iram: vaddr e084e000, va 0xe084e200 pa 0x904043 attr 0x2
[ 0.310661]
[ 0.310664] mx6sl_ddr: vaddr e0856000, va 0xe0856200 pa 0x905043 attr 0x2
[ 0.318991]
[ 0.318994] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149
[ 0.329831]
[ 0.329834] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149
[ 0.344184]
[ 0.344187] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149
[ 0.356327]
[ 0.356331] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149
[ 0.366732]
[ 0.366735] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149
[ 0.376635]
[ 0.376637] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149
3.0.35-lab126 #1 PREEMPT Thu Jul 27 04:48:26 PDT 2017 armv7l
Press [ENTER] for recovery menu... 0 //dev/mmcblk0p4:
CHS=4/16/99776 size=3269459968 bytes
flag type first last lba first lba size
Partition p1:
0x00 0x0b 16 <large> 16 6385648
CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
BOOTING DEFAULT.
IP-Config: no devices to configure
kinit: Mounted root (ext3 filesystem) readonly.
init started: BusyBox v1.17.1 (2017-07-27 04:40:39 PDT)
starting pid 625, tty '': '/etc/init.d/rcS'
/etc/init.d/rcS: line 85: boot_milestone: not found
system: I rcS:def:starting /etc/rcS.d/S50diags
USER=root
prevlevel=N
HOME=/
runlevel=S
TERM=vt102
PATH=/sbin:/bin:/usr/sbin:/usr/bin
SHELL=/bin/sh
PWD=/
VERBOSE=no
READ_AHEAD=4
USER=root
prevlevel=N
HOME=/
runlevel=S
TERM=vt102
PATH=/sbin:/bin:/usr/sbin:/usr/bin
SHELL=/bin/sh
PWD=/
VERBOSE=no
IO_SCHED=anticipatory
USER=root
prevlevel=N
HOME=/
runlevel=S
TERM=vt102
PATH=/sbin:/bin:/usr/sbin:/usr/bin
SHELL=/bin/sh
PWD=/
VERBOSE=no
TMP_SIZE=32M
info firsttime:mount_rw:time=6350:Mounting root RW for first boot
info firsttime:cursor:Linking Xorg cursor:
ln: /usr/share/fonts/X11/misc/cursor.pcf: No such file or directory
info firsttime:mount_ro:time=6380:Mounting root RO
[ 6.446829] elevator: type
[ 6.446834] not found
[ 6.451987] elevator: switch to
[ 6.451991] failed
[ 6.465873] elevator: type
[ 6.465878] not found
[ 6.471031] elevator: switch to
[ 6.471034] failed
[ 6.484767] elevator: type
[ 6.484772] not found
[ 6.489988] elevator: switch to
[ 6.489992] failed
info system:start:time=6490:
/etc/rcS.d/S50diags: line 500: f_proto: not found
info hardware:no_wan::WiFi only device. No WAN found
info system:config:platform=wario,board=muscat,rev=7,proto=N,wifi=Y,wan=N:
info system:done:time=6900:
ls: /lib/firmware/cyttsp4/muscat*.bin: No such file or directory
info cyttsp4:update:cyttsp4 fw ver=0097 file version=.bin:
/etc/upstart/cyttsp: line 49: syntax error: 0x.bin
crit modules:modprobe_failed:failed to load touch module:
/etc/rcS.d/S50diags: line 500: iptables-restore: not found
/opt/ar6k/include/dbglog.h.save: No such file or directory
info userstore:run:time=8200,action=start:
info userstore:start:found_bootup_flag:Found BOOTUP flag file
dosfsck 2.11 (12 Mar 2005)
dosfsck 2.11, 12 Mar 2005, FAT32, LFN
Checking we can access the last sector of the filesystem
Boot sector contents:
System ID "mkdosfs"
Media byte 0xf8 (hard disk)
512 bytes per logical sector
8192 bytes per cluster
2134 reserved sectors
First FAT starts at byte 1092608 (sector 2134)
2 FATs, 32 bit entries
1594880 bytes per FAT (= 3115 sectors)
Root directory start at cluster 2 (arbitrary size)
Data area starts at byte 4282368 (sector 8364)
398580 data clusters (3265167360 bytes)
32 sectors/track, 64 heads
0 hidden sectors
6385648 sectors total
Checking for unused clusters.
Checking free cluster summary.
/dev/loop/0: 864 files, 32135/398580 clusters
Wifi cal bin symbolic link AR6003_calfile.bin is already created
system: I mntroot:def:Making root filesystem writeable
/etc/rcS.d/S50diags: line 13: /usr/local/sbin/dropbearkey: not found
system: I mntroot:def:Making root filesystem read-only
/etc/rcS.d/S50diags: line 13: /usr/local/sbin/dropbear: not found
mounting waveform filesystem
waveform filesystem already mounted
info display:update:Checking '/opt/eink/images/R206_ED060KD1C4' for overrides:
umounting waveform filesystem
drawing default
cannot find image: /opt/amazon/low_level_screens/splash.png
info display:started:time=9890:
/etc/upstart/battery-diags: line 91: f_proto: not found
info battery:charged:cap=100,mV=4158,mAH=1420:
USER=root
prevlevel=N
OLDPWD=/
HOME=/
runlevel=S
TERM=vt102
PATH=/sbin:/bin:/usr/sbin:/usr/bin
SHELL=/bin/sh
PWD=/dev
VERBOSE=no
LD_LIBRARY_PATH=/usr/lib/tts/speech/components/common/:/usr/lib/tts
/etc/rcS.d/S50diags: line 13: kb: not found
diags : /opt/factory/rootfs_md5_list not found.
Change list is: [321316]
Sending: mkdir -p /mnt/base-us/diagnostic_logs/
PostMode len = 6 of 16
Ignoring PostMode
DiscoveryObjectImpl:getDeviceDiagsInfo FOUND: MUSCAT_WFO: [067] [103] with 067070918133198Y
Device found: MUSCAT_WFO [067] [103]
GlobalHalImpl: found DeviceType: 0x67
found: cyttsp4_i2c
found: cyttsp4_core
found: cyttsp4_mt_b
[ 10.098446] cyttsp4_device_access_init: Registering device access device for core_id: main_ttsp_core
[ 10.108575] cyttsp4_device_access cyttsp4_device_access.main_ttsp_core: cyttsp4_device_access_probe
[ 10.118541] cyttsp4_device_access_init: Cypress TTSP Device Access (Built 20121109) rc=0
Input driver version is 1.0.1
Input device ID: bus 0x0 vendor 0x0 product 0x0 version 0x0
Input device name: "max77696-onkey"
Supported events:
Input driver version is 1.0.1
Input device ID: bus 0x0 vendor 0x0 product 0x0 version 0x0
Input device name: "cyttsp4_mt"
Supported events:
failed to open /dev/input/event2
failed to open /dev/input/event3
failed to open /dev/input/event4
failed to open /dev/input/event5
failed to open /dev/input/event6
failed to open /dev/input/event7
Ignoring PostMode
diag>open_device m_vsInfo.xres: 1072
get_m_test_xmlFile wfo.xml
device type = 0x67
PCBID: 067070918133198Y
TCP_IP_Server_Handler:start_USBnet Enabling USB net
Cannot open xmlFile /mnt/base-us/USBnet.xml
NOT Found NFS path
[ 10.315982] unregistered gadget driver 'g_file_storage'
ERROR: Module g_serial does not exist in /proc/modules
[ 10.375718] usb0: MAC ee:59:00:00:00:15
[ 10.379562] usb0: HOST MAC ee:29:00:00:00:15
[ 10.383838] g_ether gadget: controller 'fsl-usb2-udc' not recognized; trying CDC Ethernet (ECM)
[ 10.415611] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[ 10.422247] g_ether gadget: g_ether ready
[ 10.431342] fsl-usb2-udc: bind to driver g_ether
system: I mntroot:def:Making root filesystem writeable
[ 10.485896] EXT3-fs (mmcblk0p2): using internal journal
sock_init 1888
I have navigated to usb export and kindle window popup my screen.
- I downloaded latest firmware from amazon and copied to kindle. After reboot it is installed successfully but the nothing was changed except that I have screen lights now.
- I tried factory firmware with some way but it refuses to install.
Now my only option is fastboot I think. But I cannot connect fastboot to device in windows10 due to the lack of a proper driver. USB linux is pain in the ass because of the UEFI and my computer's recovery which interferes many distros I have tried.
I need some good advice to go on...
