Hello everyone!
I am trying to fix a PW3 (DP75SDI with S/N starting by G090KB).
It doesn't boot at all and does nothing when connected to a PC by USB.
Silly me, I thought all DP75SDI were the same and I swapped the faulty board with another working DP75SDI board, but it turns out the working board is from a PW2, and now my screen shows as half black half white with black lines. I hope this didn't break the screen :blink:
Back to the faulty PW3 board, I am trying to see if it's possible to recover it.
When connected to the serial port, I get this (I am using CuteCom on a Rpi4):
And that's it, I don't have a clue about how to proceed now. Read about some recovery/forensic images on ixtab .tk but the site seems down.
How do I continue?
I am trying to fix a PW3 (DP75SDI with S/N starting by G090KB).
It doesn't boot at all and does nothing when connected to a PC by USB.
Silly me, I thought all DP75SDI were the same and I swapped the faulty board with another working DP75SDI board, but it turns out the working board is from a PW2, and now my screen shows as half black half white with black lines. I hope this didn't break the screen :blink:
Back to the faulty PW3 board, I am trying to see if it's possible to recover it.
When connected to the serial port, I get this (I am using CuteCom on a Rpi4):
Code:
[13:56:51:226] U-Boot 2009.08-lab126 (Feb 04 2020 - 07:55:13)
[13:56:51:226]
[13:56:51:226] CPU: Freescale i.MX6 family TO0.0 at 996 MHz
[13:56:51:226] Temperature: 37 C, calibration data 0x5d95575f
[13:56:51:226] mx6sl pll1: 996MHz
[13:56:51:226] mx6sl pll2: 528MHz
[13:56:51:226] mx6sl pll3: 480MHz
[13:56:51:226] mx6sl pll8: 50MHz
[13:56:51:226] ipg clock : 66000000Hz
[13:56:51:226] ipg per clock : 24000000Hz
[13:56:51:226] uart clock : 80000000Hz
[13:56:51:226] cspi clock : 60000000Hz
[13:56:51:226] ahb clock : 132000000Hz
[13:56:51:226] axi clock : 198000000Hz
[13:56:51:226] emi_slow clock: 22000000Hz
[13:56:51:226] ddr clock : 396000000Hz
[13:56:51:226] usdhc1 clock : 198000000Hz
[13:56:51:226] usdhc2 clock : 198000000Hz
[13:56:51:321] usdhc3 clock : 198000000Hz
[13:56:51:321] usdhc4 clock : 198000000Hz
[13:56:51:321] MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
[13:56:51:385] Board: Muscat WFO
[13:56:51:385] Boot Reason: [ POR ]
[13:56:51:385] Boot Device: NAND
[13:56:51:385] Board Id: 0670509174530R1M
[13:56:51:385] S/N: G090KB and the rest of the S/N
[13:56:51:385] I2C: ready
[13:56:51:385] DRAM: 512 MB
[13:56:51:385] Using default environment
[13:56:51:385]
[13:56:51:385] In: serial
[13:56:51:385] Out: serial
[13:56:51:385] Err: serial
[13:56:51:385] Quick Memory Test 0x80000000, 0x1fff0000
[13:56:51:481] POST done in 111 ms
[13:56:52:457] Battery voltage: 3713 mV
[13:56:52:457]
[13:56:52:457] Hit any key to stop autoboot: 1 <0x08><0x08><0x08> 0
[13:56:54:418] ## Booting kernel from Legacy Image at 80800000 ...
[13:56:54:418] Bad Header Checksum
[13:56:54:418] ERROR: can't get kernel image!
[13:56:54:418] uboot >How do I continue?